I love our bamboo shades (we have them both in the kitchen and in our new bedroom—we bought these and they are currently unavailable, but there are lots more on Amazon). They look great, came in a ton of custom sizes and were inexpensive.
However, they aren't lined and let a whole lot of light in:
Don't get me wrong—we love our little lake view (as does Susie)...
But some days I just wanna sleep in. Or take a nap at 2pm. We had blackout curtains in our old bedroom so I wasn't used to all this light and was getting tired of covering my face with a pillow.
Simple fix: a $10 piece of fabric and some hot glue.
I must have wandered the aisles of JoAnn's for nearly an hour looking for the perfect liner. I later found that blackout liner exists and can be purchased, but I didn't see any there—guess I wasn't looking hard enough?
I finally settled on this velvet-like taupe colored material that I thought would be camouflaged nicely by the bamboo blinds.
Demonstrating its light blocking power...
Looks good to me!
Next I had to trim it to the exact width of the blinds. This was a challenge because it wasn't really a perfect rectangle—the bamboo slats kept shifting and it was hard to line everything up perfectly.
I used a big ruler, a cutting mat and an Xacto knife and just carefully trimmed, one section at a time...
I could have used regular scissors but I didn't have any sharp enough to cut a smooth line. The Xacto knife paired with some tension on the fabric did the trick.
With trial and error, it was finally cut to size:
I decided not to run the fabric the entire length of the shades because the window wasn't tall enough for it to expand all the way, so the bottom of the shade was bunched up and didn't need liner.
Before attaching the liner, I untied and removed the drawstrings so that they would run on the outside of the liner and it would roll up properly.
I just had to poke holes where it looped to the back, and then cut slits where the rings were.
Attaching it was easy—I just placed a dot of hot glue on each of the large slats, right along the edge:
I repeated along the top, on both edges and added a few beads of glue along the center for good measure.
Then I poked the rings through the slits I had made, threaded the string and tied it back to the bottom ring.
Then I held my breath and crossed my fingers...
And it worked! I was a little nervous that the fabric would be too thick for it to roll back up properly, but it was no problem at all.
Check it out now...
So much better, right?
See how dark it is when I turn the lights off?
Success!
We also decided to remove our center light fixture and swap it out for a ceiling fan.
Flashback to a few weeks ago since this is the best photo of the old fixture I could find...
We wanted something small and simple to fit the scale of the room. We love the fan in our sunroom...
So I checked back on Amazon to make sure it was still available, and sure enough, it was! Sold.
We (well, Brad) installed it this morning.
Yay for circulation.
Switching pages here... it's about time for an office update!
Here it was the last time you saw it:
Well guess what? I got myself a little present:
I shouldn't say little. This thing is massive. And it's the whole reason for the room switch.
Of course... if you follow me on instagram or facebook you would have known this a while ago ;)
Behold, the awesomeness:
I'm so excited.
We also set up a temporary workstation... but then we had cover it up so we could do our next project...
Recessed lighting.
For this project, Brad tried out some new lights:
He said it was the easiest recessed light install he's done and highly recommends these kits.
For the bulbs, Brad bought seven 10 watt LED daylight bulbs (the brightest he could find) for $11.88/ea on Amazon.
We decided to remove the chandelier (it would get in the way) and put our old office light fixture back in its place. I can flip it on when I just need a little light for a more cozy work environment.
If anyone was curious, here's the mounting bracket and wiring situation we had going on behind our TV when it was wall mounted:
That's all gone now and we're going to remove the electrical boxes and patch over the holes since I have other plans for that wall.
After the lights and new printer were in, we made a trip to Lowe's to pick up some materials to build a much needed large desk for cutting my big 'ol posters.
Unfortunately, Ikea didn't have any wider desks to match my existing setup, but fortunately, Lowe's had some melamine panels that was a close match to my desk tops. On a recent Ikea trip, I picked up a handful of extra desk legs so that the new desk would be the same height.
The panels were 4x8 feet and 3/4" thick. I needed something more substantial so I bought two to stack them. I also had Lowe's cut them to 4x6' to work better with my room arrangement.
It was $38/panel, so not exactly cheap, but then again you can't beat a large custom desk for less than $100.
We laid the panels out on the floor and made sure they were aligned:
Then Brad installed the legs:
Finally, we inserted some screws that were long enough to grab both boards to hold them together, and it was ready to go:
Everything lined up perfectly! It was meant to be. Lowe's saves the day.
I still need to pick up some sort of wood edging to conceal the bare sides.
Once that's done, it should look like a nice custom setup. Oh, and ignore the chaos. It's going to be like this for a while.
While at Lowe's, I also picked up something fun for the back wall...
I was going to go with my usual board & batten treatment, but I saw these panels and decided to switch things up.
The printer will be relocating to this wall, and I'm going to run trim and a little shelf ledge along the top. I think it will be a nice touch.
That is my project for next week, so hopefully it will be completed by next Sunday!
I'll have to leave you all in anticipation until then...
No comments:
Post a Comment